Air Gun Maintenance

posted on October 19, 2016
In this article I will focus primarily on compressed air rifles and pistols. Compressed air, as powered by SCUBA tanks or high-pressure hand pumps, is also known as CA or PCP (Pre-Charged Pneumatic).

The first issue with a CA gun is transferring the air charge from the fill apparatus into the gun’s cylinder. At this point in the match air gun market, I know of only one manufacturer that uses a non-detachable cylinder—the Air Arms Pistol. All other brands of 10m air rifles and pistols use a removable cylinder that mounts under the barrel and should be easily removed with hand pressure alone.

I am assuming you have already figured out whether you are using a high-pressure pump or a SCUBA tank to fill your cylinder and know how to remove it. When reinstalling your cylinder, you should never use tools to tighten a CA cylinder onto the gun. You can easily over-tighten it and damage the threads. Every time you install the cylinder on the gun, you should visually inspect that there is no dirt or other debris adhering to the threads. If you see any foreign objects, you should thoroughly clean the thread with something that has hard plastic bristles like a toothbrush.

While you are looking at the cylinder threads, inspect for any grease. A very small “smidgeon” of synthetic grease should be applied to the threads every 20 to 30 times that you remove the cylinder. This “smidgeon” should only be about the size of a pinhead. Too much grease is just as bad as not enough. You can also apply a very small amount of the same grease to the end of your finger and smear some on the sealing o-ring or the surface that meets the sealing o-ring on the cylinder. (Some manufacturers have the o-ring on the cylinder and others place it inside the action.) It is VERY IMPORTANT that you do not get any grease or oil near the air valve on the end of the cylinder. This periodic lubing will prevent galling between the cylinder threads and receiver mount. Some brands of 10m guns are known to become dry and gall badly, thus freezing the cylinder in place. When such a cylinder is finally removed with great force, it will have stripped, leaving a major portion of the threads unusable. This will result in a trip to your air gun smith where he or she will give you the bad news—that your cylinder and receiver block will have to be replaced.

I mentioned synthetic grease, so let’s talk about proper lubricants for modern CA guns. Never use a petroleum-based lubricant or cleaner with your air gun. If the petroleum product gets into the high-pressure line, it can diesel (ignite) and cause a potential life threatening explosion. Also, non synthetic oils or cleaners can cause the rubber or plastic seals to deteriorate. Most traditional firearm lubes and solvents will harm your air gun. The good news is that you don’t need to lube an air gun very often or very much. Honestly, we see more air guns damaged from over-lubing than under-lubing. If you want to lubricate your gun, all you need is a very little amount of synthetic grease on the working parts of levers or pins and a “smidgeon” of moly grease on the sear and the cylinder threads, as mentioned above. In normal use, the only user lubrication that I would consider absolutely necessary is the grease on the cylinder threads. Other lubrication can take place when you have a professional check-up of your air gun.

How often should that happen? It depends on how much you use it. Top athletes that are shooting daily should have their guns gone through once a year. Schools or programs that shoot their guns half a year or so can get by with a rifle service every third year. Individuals who shoot their air guns infrequently can go six or seven years or longer. What does a full service consist of? Normally, all seals and springs will be replaced. Valves and valve surfaces will be inspected and replaced if necessary. This necessitates disassembling the whole gun, so all moving parts will get inspected and re-lubed on re-assembly and any potential problems should be found. As I heard one shooting athlete say to another, “Getting your rifle rebuilt is a good idea, because sometimes they just find stuff.”

Preserve the Life of your Air Gun
One thing you can do to preserve the life of your air gun is unscrew the cylinder every time you finish shooting it for the day. Unscrew it enough that you hear the air “whoosh” out of the regulator. Leave the cylinder attached to the gun to prevent dirt or other foreign objects getting on the threads. When you get ready to re-install the cylinder, unscrew it all the way out first, and then start back in to avoid pinching the sealing o-ring. The reason for releasing the air is to take the pressure off the regulator springs and o-rings—the heart of a modern CA match rifle. The regulator is what steps the 3,000 PSI air in the cylinder down to around 850 PSI to give a consistent shot each time you pull the trigger.

With a CA air gun, shoot a few shots without pellets before starting sighters to make sure that the internal rubber seals are moving properly.
Another point about regulators on CA guns is to exercise them after the gun has set for a while. Shoot three or four shots without pellets before starting sighters to make sure that the internal rubber seals are moving as they should, as sometimes they can stick when the have set for awhile.

Another frequently asked question is: Does your air rifle barrel require cleaning? There is some debate on this issue. There are those who say it should be cleaned every time after firing, and those who say to never clean an air gun barrel. Air guns don’t generate any real heat, nor do they have dirty powder residue like firearms. I have tested many air guns for pellet accuracy and, occasionally, found one that does not shoot well. I tried cleaning the barrel, looking for improvement, and it seldom helps. If you are using good quality match pellets from RWS, H&N, Vogel or JSB, then cleaning is of little benefit. If you think it helps, don’t let me discourage you. I recommend you use some doubled up monofilament fishing line to pull a cleaning batch through the barrel. I see no need to ever put a brush or a rod through a 10m air gun barrel unless you have a pellet stuck in the bore. A barrel that has been cleaned should have 15 to 20 “fouling shots” shot through it before you start a match, as a totally clean barrel will shoot to a different point of impact than one with a normal amount of pellet wax on the lands and grooves.

Always make sure that pellet holders are securely closed in your travel case. Every year we get three or four guns that have problems. When we dissemble the action, we find little chunks of pellet lead from the gun case that somehow got inside the action.

For those that use a CBI (Clear Barrel Indicator), you should carry something like a sandwich baggie to store the CBI when not being used. I cringe every time I see an athlete remove a CBI and throw it on the dirty floor, then pick it up and stuff it back into the barrel at the end of the shooting session. This can cause long term damage to either the rifling or the crown of your precision air gun.

All these basic rules apply to air rifles using CO2 as well. For more information on air gun maintenance, see Additionally, for supplies, forums and other related resources, contact PILKGUNS at (931) 924-3400 or


2024Usahighschoolclaytarget 2
2024Usahighschoolclaytarget 2

Champions Crowned At 2024 USA High School Clay Target League National Championship

Brody Lenington topped the 2024 USA High School Clay Target League National Championship leaderboard to win the overall title, while Madelyn Coats picked up the women’s individual title.

Paris 2024: U.S. Paralympic Shooting Team Roster

Six talented rifle and pistol athletes will represent the red, white and blue at the upcoming Paris 2024 Paralympic Games.

Winchester Celebrates 25 Years As Ammunition Provider To Kids & Clays Foundation

For 25 years, Winchester has stood strong as a source of ammo for Kids & Clays shooting tournaments that raise funds to support Ronald McDonald House.

Paris 2024 U.S. Olympic Shooting Team Preview

While the U.S. shooting team has a few prior medalists, the roster for the Paris 2024 Games also includes several shooters making their Olympic debut in France this month.

What’s In Your Range Bag, James Hall?

Learn what top men’s air pistol shooter James Hall keeps in his range bag.

U.S. Paralympic Shooting Team Secures Nine Medals At WSPS Arequipa Grand Prix

At the 2024 WSPS Arequipa Grand Prix, U.S. Paralympic shooters picked up nine medals, including three golds.


Get the best of Shooting Sports USA delivered to your inbox.