Loading Double-Action And Single-Action Revolvers

by
posted on October 30, 2021
** When you buy products through the links on our site, we may earn a commission that supports NRA's mission to protect, preserve and defend the Second Amendment. **
rimfire-revolvers-smith-wesson-617.jpg

Loading double-action and single-action revolvers involves two separate and very different procedures. Here are specific techniques for performing this function with both types.

Loading Double-Action Revolvers

Almost all double-action revolvers feature a swing-out cylinder operated by a latch that, in most models, is located on the left side of the frame. With the revolver held in the right hand (for both right- and left-handed shooters), pointed in a safe direction with the trigger finger outside the trigger guard and alongside the frame, the cylinder latch is engaged with the right-hand thumb. Note that a few revolver models locate the cylinder latch on the crane, engaging the latch must be done with the left hand.

Smith & Wesson JM revolver
Smith & Wesson Performance Center Model 929 revolver.


With the cylinder latch disengaged, the left hand is placed around the frame and the left-hand fingertips push the cylinder out of the frame, to the left. The cylinder should never be swung out violently, as is sometimes seen in feature films, this causes damage to the revolver.

Once the cylinder is fully open, the revolver's muzzle is pointed slightly downward. With the revolver held in the left hand, live cartridges are inserted, one by one, into the chambers of the cylinder with the right hand. When the cylinder is full, the left-hand thumb pushes it fully back into the frame. A click will be heard when the cylinder is locked in place by the cylinder latch.

At this point, the revolver is ready to fire. A firing grip may be obtained with the right hand (for right-handed shooters) or the left hand (for left-handed shooters).

Loading Double-Action Revolvers
When beginning to load a double-action revolver, it should be held in the right hand and the cylinder latch operated by the right thumb (A). Once the cylinder latch is disengaged, the left hand is placed around the frame and the left-hand fingers push the cylinder to the left (B). This exposes all the chambers (C). The gun's muzzle is pointed slightly downward and live cartridges are inserted into the chambers, one by one (D). When the cylinder is full, it is swung back into the frame until it locks closed (E).


Loading Single-Action Revolvers

Instead of a cylinder that swings out, single-action revolvers usually have a right-side loading gate that is swung open to allow access to one chamber at a time.

For a right-handed shooter, the revolver is initially held in the right hand, the hammer put in the half-cock position (on some models), and the loading gate opened with the right-hand thumb. The gun is then transferred to the left hand and is turned slightly counterclockwise, with the muzzle pointed downward (but still in a safe direction). Next, the cylinder is rotated to expose an empty chamber. A fresh cartridge is inserted into the chamber with the right hand, and then the chamber is rotated to expose the next empty chamber. This process is repeated until all the chambers are full, at which point the loading gate is closed.

For left-handed shooters, the revolver is held in the left hand, the hammer is placed in the half-cock position if necessary, and the loading gate opened with the right-hand thumb. With the gun rotated slightly counterclockwise and held with the muzzle down (but still pointed in a safe direction), the cylinder is rotated with the right hand until an empty chamber is fully exposed, and a fresh cartridge inserted into it. The cylinder is rotated to expose the next empty chamber, and the loading process is repeated until all the chambers are full, at which point the loading gate is closed.

Loading Single-Action Revolvers
To load a single-action revolver (for a right-handed shooter), transfer the gun to the left hand and use the right thumb to engage the loading gate located on the right side of the frame (A). Open the gate and rotate the cylinder to expose an empty chamber (B). With some revolver designs, the hammer must be put in the half-cock position before the loading gate can be opened and the cylinder rotated. Insert a live cartridge into the empty chamber (C), and continue the process until the cylinder is full, at which point the loading gate is closed (D).


Lead photo: Smith & Wesson Model 617 Rimfire.


Read more: Handgun Operation: Semi-Automatic Safety Mechanisms

Latest

USAHSCTL Nationals2025 3
USAHSCTL Nationals2025 3

Nicholas Coppage Tops Field At 2025 USA High School Clay Target Nationals

Nicholas Coppage wins 2025 national clay target title after a perfect final round and epic shoot-off, Beaver River Central H.S. receives team title.

New: Metal Madness Easy Up Target Frames

A simpler setup with more affordable gear makes Metal Madness steel shooting more accessible than ever.

NRA Announces Dianna & Ryan Muller As Brand Ambassadors For America’s Rifle Challenge

NRA announces Dianna & Ryan Muller as brand ambassadors for America’s Rifle Challenge program, promoting AR-15 marksmanship, safety and training.

Eley’s New Trial Packs Let Competition Shooters Find Their Perfect Rimfire Match Ammo

Eley launches trial ammo packs to help shooters test and match precision .22 LR rounds to their firearms.

Ava Downs Captures Junior Olympic Trap Title On Home Turf

Hillsdale’s Ava Downs takes gold in women’s trap at the 2025 USA Shooting Junior Olympic Championships hosted at the Halter Center.

Brandon Powell Claims 8th Georgia State Sporting Clays Title

Brandon Powell wins his eighth Georgia State Sporting Clays Championship, continuing his dominance with multiple top finishes at the 2025 tournament.

Interests



Get the best of Shooting Sports USA delivered to your inbox.