Unloading Double-Action And Single-Action Revolvers

by
posted on November 13, 2021
revolver-unload-1.jpg

The mechanisms of double-action and single-action revolvers require unloading procedures that are very different. (Be sure to read these beginner's guides covering revolver loading and firing processes.)

Unloading Double-Action Revolvers

With the revolver held in the right hand, the trigger finger outside the trigger guard and the muzzle pointing in a safe direction, the right thumb disengages the cylinder latch (except in those in models where the latch is on the crane, which requires the use of the left hand). The fingers of the left hand encircle the frame and push the cylinder out of the frame, to the left. With the cylinder fully open, the shooter may choose two methods of removing spent cases and live cartridges from the chamber. With the revolver's muzzle pointing slightly downward, the shooter may push rearward on the ejector rod, raising both the brass cases and live cartridges out of the cylinder. This allows them to be removed, one by one, from the chambers using the right hand (while the left hand supports the revolver).

Unload double-action revolver
To unload a double-action revolver, grasp the gun in the right hand and disengage the cylinder latch (A). The cylinder is pushed out to the left, in the same manner as when starting the loading procedure. The ejector rod is then pushed fully rearward (B) with the left-hand thumb to extract the spent cartridge cases or live cartridges, which may then be removed manually. Alternatively, the revolver may be pointed upward, and the ejector pressed smartly with the right hand (C) to drop the empty cartridge cases and live cartridges out of the chambers.


Alternatively, the shooter may hold the gun in the left hand with the cylinder open and the left hand fingers through the opening in the frame that is normally occupied by the cylinder. The muzzle is then pointed straight up, and the left-hand thumb forcefully pushes the ejector rod downward. If hard extraction is encountered, the ejector rod may be hit sharply with the palm of the right hand. Either technique will have the effect of forcefully extracting all the brass and live cartridges from the chambers and dropping them simultaneously out of the cylinder. This technique is used when the shooter wishes to reload the revolver quickly.

Unloading Single-Action Revolvers

As with the loading process, the single-action revolver can be unloaded with the revolver in held in either hand.

Unload Single-Action Revolvers
To unload a single-action revolver, the gun is grasped in the firing hand, with the trigger outside the trigger guard and the hammer down (A). The loading gate is opened (B), and the cylinder is rotated to align an empty case or live cartridge with the opening gate (C). Note that some revolver designs require that the hammer be in the half-cock mode for the loading gate to be opened and the cylinder rotated.


With the revolver held in the right hand, the trigger finger outside of the trigger guard and straight alongside the frame, and the muzzle pointed in a safe direction, the hammer is put in the half-cock position (with some models), and the loading gate opened with the right thumb. The cylinder is rotated until a cartridge case head is fully visible, and then the ejector, located under the barrel, is pulled to the rear, pushing the live round or empty brass out of the chamber. The ejector is allowed to return forward, the cylinder is rotated to the next chamber, and the process is repeated until all chambers are empty.

Single-Action Revolver
With an empty case or live cartridge aligned with the loading gate, the index finger of the firing hand engages the ejector rod (D) and pulls the rod rearward to push the case out of the chamber (E), where it is manually removed. The cylinder is rotated to the next chamber, and the process repeated until the revolver cylinder is empty.


For left-handed shooters, the unloading process starts with the revolver in the left hand. With the trigger finger outside of the trigger guard and straight alongside the frame, and the muzzle pointed in a safe direction, the hammer is put in the half-cock position (if necessary), and the loading gate opened with the right hand. The cylinder is rotated until a cartridge case head is fully visible, and then the ejector, located under the barrel, is pulled to the rear, pushing the live cartridge or empty brass out of the chamber. The ejector is allowed to return forward, the cylinder is rotated to the next chamber, and the process is repeated until all chambers are empty.

Decocking

For a variety of reasons, it may become necessary for a shooter firing a single-action revolver, or a double-action revolver in single-action mode, to lower the hammer on a chamber containing a live cartridge.

To properly lower the cocked hammer of a revolver, first take the trigger finger off the trigger and put it outside the trigger guard, along the frame. Place the support-hand thumb in between the cocked hammer and the frame, and engage the hammer spur with the firing-hand thumb. Pull the trigger, being careful to control the released hammer with the firing-hand thumb. The placement of the support-hand thumb between the hammer and frame prevents the hammer from setting off the cartridge, if it slips.

When the hammer contacts the support-hand thumb, release the trigger and place the trigger finger outside the trigger guard, alongside the frame. Then, with the firing-hand thumb still controlling the hammer, remove the support-hand thumb from between the hammer and frame, and ease the hammer the rest of the way down. The revolver may be unloaded.


Read more: Accurately Calling Your Shots

Latest

AREA 7 STEEL CHALLENGE CHAMPIONSHIP 2024 2
AREA 7 STEEL CHALLENGE CHAMPIONSHIP 2024 2

All About The 2024 Area 7 Steel Challenge Championship

After successfully defending his title this year, Phil Strader has won Production division at the Area 7 Steel Challenge Championship three out of the four years he has competed in it.

WATCH: Labradar LX Compact Shooting Chronograph

Much smaller than the original Labradar released a decade ago, the new LX compact shooting chronograph packs a Doppler radar system into a tiny footprint.

Unified Effort By Military And Civilians To Advance Marksmanship: 1962 National Matches

The 1962 NRA National Matches are an outstanding example of a unified effort by members of the military and civilians with a shared heritage and a common interest in marksmanship.

Battle At The Peak: USPSA Colorado State Championship Beats Weather Again

This year’s USPSA Colorado State Championship at Pikes Peak Gun Club in Colorado Springs featured 12 challenging stages and a round count of 333.

Mental Defeat To World Champion

At the 2024 IPSC Rifle World Shoot in Finland this summer, Justine Williams learned that a match isn’t over until the last shot is fired.

Review: Glock G17L Gen5 MOS

Made for competition, the optics-ready Glock G17L sports a longer barrel and a lighter trigger pull.

Interests



Get the best of Shooting Sports USA delivered to your inbox.